2014年2月20日星期四
Configuring the Sub-interface
Configure
ME60
<HUAWEI>
system-view
[HUAWEI]
sysname ME60A
[ME60A]
interface pos 1/0/0
[ME60A-Pos1/0/0]
link-protocol fr
[ME60A-Pos1/0/0]
undo shutdown
[ME60A-Pos1/0/0]
quit
[ME60A]
intrface pos 1/0/0.1 p2p
[ME60A-Pos1/0/0.1]
ip address 202.38.160.1 255.255.255.0
[ME60A-Pos1/0/0.1]
undo shutdown
[ME60A-Pos1/0/0.1]
fr dlci 50
[ME60A-fr-dlci-Pos1/0/0.1-50]
quit
[ME60A]
interface pos 1/0/0.2 p2p
[ME60A-Pos1/0/0.2]
ip address 202.38.161.1 255.255.255.0
[ME60A-Pos1/0/0.2]
undo shutdown
[ME60A-Pos1/0/0.2]
fr dlci 60
[ME60A-fr-dlci-Pos1/0/0.2-60]
quit
[ME60A]
ip route-static 129.10.0.0 255.255.0.0 202.38.160.2
[ME60A]
ip route-static 129.11.0.0 255.255.0.0 202.38.161.2
NOTE:
This
example mainly explains sub-interface configuration. ME60 B and ME60-X3 do not
require sub-interfaces configuration.
2014年2月18日星期二
Configuration Example of the RADIUS Authentication
The MA5620 is interconnected with the RADIUS server through the RADIUS protocol to implement authentication.
Configure
the authentication scheme.
Configure authentication scheme newscheme (users are authenticated through RADIUS).
huawei(config)#aaa
huawei(config-aaa)#authentication-scheme
newscheme
huawei(config-aaa-authen-newscheme)#authentication-mode
radius
huawei(config-aaa-authen-newscheme)#quit
huawei(config-aaa)#quit
Configure
the RADIUS protocol.
Create RADIUS server template template1. RADIUS server 10.10.66.66 functions as the primary authentication server, and RADIUS server 10.10.66.67 functions as the secondary authentication.
huawei(config)#radius-server
template template1
Note: Create a new server template
huawei(config-radius-template1)#radius-server
authentication 10.10.66.66 1812
huawei(config-radius-template1)#radius-server
authentication 10.10.66.67 1812 secondary
huawei(config-radius-template1)#quit
Create
a domain.
Create domain isp1.
huawei(config)#aaa
huawei(config-aaa)#domain
isp1
Info: Create a new domain
Reference
the authentication scheme.
You
can reference an authentication scheme in a domain only after the
authentication scheme is created.
huawei(config-aaa-domain-isp1)#authentication-scheme
newscheme
Reference
the RADIUS server template.
You
can reference a RADIUS server template in a domain only after the RADIUS server
template is created.
huawei(config-aaa-domain-isp1)#radius-server
template1
huawei(config-aaa MA5680T -domain-isp1)#quit
2014年2月12日星期三
How to configuring Huawei MA5600
Configure MA5600 the IP address of the L3 interface.
huawei(config)#vlan
2 smart
huawei(config)#port
vlan 2 0/7 0
huawei(config)#interface
vlanif 2
huawei(config-if-vlanif2)#ip
address 10.0.0.1 24
huawei(config-if-vlanif2)#quit
Enable
OSPF and specify the area ID to which the interface belongs.
huawei(config)#ospf
huawei(config-ospf-1)#area
0
huawei(config-ospf-1-area-0.0.0.0)#network
10.0.0.0 0.0.0.255
huawei(config-ospf-1-area-0.0.0.0)#quit
huawei(config-ospf-1)#quit
Configure
the OSPF router ID.
huawei(config)#router
id 1.1.1.1
Configure
three static routes.
huawei(config)#ip
route-static 20.0.0.1 32 vlanif 2
huawei(config)#ip
route-static 30.0.0.1 32 vlanif 2
huawei(config)#ip
route-static 40.0.0.1 32 vlanif 2
Import
static routes into the OSPF routing table to improve its capability of
obtaining routes.
huawei(config)#ospf
hawei(config-ospf-1)#import-route
static
hawei(config-ospf-1)#quit
Save
the MA5600T data.
huawei(config)#save
2014年2月11日星期二
5680t 813e data do
MA5680T 813e, the data do, what is the business of the VLAN command?
8.1
EPON ONT template
EPON
ONT template includes DBA template, template, template line business, this task
introduce these template configuration.
8.2
create VLAN
Creating
the VLAN VLAN base configuration and business, in the VLAN configuration before
the need to ensure that VLAN has been created according to the actual planning.
8.3
uplink port configuration
Uplink
docking port and the upper equipment, in order to make the data on the device
can be forwarded to the network through the uplink port, and transmitting data
upper network forwarding to the uplink port user side.
Configure
EPON ONT 8.4
MA5680T/MA5683T
provides services to end users through the ONT, MA5680T/MA5683T and ONT channel
up, MA5680T/MA5683T to manage ONT, ONT to work properly.
Configure
the EPON port 8.5
The
Huawei GPON port must be opened to work properly and bearing business, the task of
open EPON port configuration port, and related properties.
8.6
to create EPON service flow
2014年2月10日星期一
Configuring Remote Port Mirroring
Remote mirroring is not applicable to the NE80E/NE40E-X3 in the LDP over TE and TE links switchover scenarios.
Run:
system-view
The
system view is displayed.
Run:
interface
interface-type interface-number
The
interface view is displayed.
Run
one of the following commands as required:
Run the port-mirroring instance-name inbound [cpu-packet ] command to observe the inbound traffic on the remote mirroring port.
Run the port-mirroring instance instance-name outbound command to observe the outbound traffic on the remote mirroring port.
Run
the port-mirroring remote { inbound | outbound } command to configure NE40E-X8 remote
port mirroring for inbound or outbound traffic.
2014年1月24日星期五
PPPoE current mirror
A
few days ago to do with MA5620 , has no, today found a 9303 try, finally!!
Observe-port
1 interface GigabitEthernet1/0/0
Add
the observation port
ACL
number 5000
Rule
1 permit 0x00000050 0x0000ffff 42
Add
user defined ACL, matching the target TCP 80 port, TCP protocol at the start of
the two layer packets of thirty-fourth bytes, 2 bytes source port, destination
port 2 bytes, 6 bytes plus PPPoE protocol, PPP protocol byte offset from the
beginning of 2, forty-second bytes
Traffic
classifier web operator or precedence 5
If-match
ACL 5000
#
Traffic
behavior Web
Mirroring
to observe-port 1
#
Traffic
policy Web
Classifier
web behavior Web
Standard
three piece suit
Interface
GigabitEthernet1/0/6
Port
link-type access
Port
default VLAN 106
Traffic-policy
web inbound
Business
application port ACL, found ACL involves two layer data only in the direction
of application, unable to make the direction
The
final catch all monitoring equipment MA5626 is the destination port for the TCP 80
package
2014年1月22日星期三
How to configure FTP for Huawei S5700 ?
When
I configure FTP for Huawei S5700 switch, I use the steps as following, but I
can’t make it work:
Step
1 seting for the FTP server
Start
the FTP service on Switch, and configure the FTP username ftpuser, password
ftppwd.
<Quidway>
System-View
[Quidway]
FTP server enable
[Quidway]
AAA
[Quidway-aaa]
local-user ftpuser password simple ftppwd - appear the mistake: Error:
Unrecognized command found at '^' position. but if input: local-user ftpuserpassword
CI ftppwd is not this tip.
[Quidway-aaa]
local-user ftpuser service-type FTP
[Quidway-aaa]
local-user ftpuser ftp-directory flash:/
[Quidway-aaa]
return
Step
2 configure device IP
The
configuration of IP, recommend the use of the idle and configured as a default
configuration interface, the Ethernet 0/0/1 as an example.
<Quidway>
System-View
[Quidway]interface
Ethernet 0/0/1 - enter the mistake this command: Error: Wrongparameter found at
position. and then give '^' not the next step.
[Quidway-Ethernet0/0/1]port
link-type access
[Quidway-Ethernet0/0/1]quit
[Quidway]
VLAN 10
[Quidway-vlan10]
port Ethernet 0/0/1
[Quidway-vlan10]
quit
[Quidway]
interface vlanif 10
[Quidway-Vlanif10]
IP address 1.1.1.1 24
[Quidway-Vlanif10]
quit
[Quidway]
Step
3 login to the FTP server (Switch)
The
following example is the WindowsXP system are described.
Storage
will upload the file to the specified directory (assumed to be the D:\>
directory), in the "Start Menu" run ", type" CMD, and then
press the "enter" key. Then type FTP 1.1.1.1,in "user"
prompt, enter the user name, in the "password" prompt, enter the
password, and then press the "enter" key. Display information as
follows:
D:\>ftp
1.1.1.1
Connected
to 1.1.1.1
220
FTP service ready
User
(1.1.1.2: (none)): ftpuser
331
Password required for 1
Password
230
User logged in
Ftp>
Step
1 upload web software
In
the FTP client (PC) to execute the put source-filename [destination-filename],
from PC upload software. Upload finished, execute the bye command, disconnect
FTP, return to the user view.
Ftp>
put D:\S2300.web.zip
200
Port command okay
150
Opening ASCII mode data connection for LS-S2326TP-SI-AC .web.zip
226
Transfer complete
Ftp:
send 4940436 bytes, when using 35.10Seconds 140.76Kbytes/sec
Ftp>
bye
221
Server closing
D:\>
订阅:
博文 (Atom)