Configuration Example of the RADIUS Authentication

The MA5600 is interconnected with the RADIUS server through the RADIUS protocol to implement authentication.

Configure the authentication scheme.

Configure authentication scheme newscheme (users are authenticated through RADIUS).

huawei(config)#aaa

huawei(config-aaa)#authentication-scheme newscheme

huawei(config-aaa-authen-newscheme)#authentication-mode radius

huawei(config-aaa-authen-newscheme)#quit

huawei(config-aaa)#quit

Configure the RADIUS protocol.

Create RADIUS server template template1. RADIUS server 10.10.66.66 functions as the primary authentication server, and RADIUS server 10.10.66.67 functions as the secondary authentication.

huawei(config)#radius-server template template1

 Note: Create a new server template

huawei(config-radius-template1)#radius-server authentication 10.10.66.66 1812

huawei(config-radius-template1)#radius-server authentication 10.10.66.67 1812 secondary

huawei(config-radius-template1)#quit

Create a domain.

Create domain isp1.

huawei(config)#aaa

huawei(config-aaa)#domain isp1

  Info: Create a new domain 

Reference the authentication scheme.

You can reference an authentication scheme in a domain only after the authentication scheme is created.

huawei(config-aaa-domain-isp1)#authentication-scheme newscheme

Reference the RADIUS server template.

You can reference a RADIUS server template in a domain only after the RADIUS server template is created.

huawei(config-aaa-domain-isp1)#radius-server template1

huawei(config-aaa-domain-isp1)#quit

Result

User1 in isp1 can be authenticated and can log in to the MA5600T

Configuring DOCSIS Event Reporting

DOCSIS 3.0 defines various DOCSIS events, such as authentication failure and CM certificate error events. Configuring DOCSIS event reporting helps you obtain MA5600T/MA5600 /MA5608T and CM running status.

The following configurations are used as an example to configure the CM management feature:

Priority of DOCSIS events: alert

Mode of reporting DOCSIS events to the U2000: trap

Mode of reporting DOCSIS events to the log host: syslog

IP address of the U2000: 10.10.10.10

IP address of the log host: 10.10.20.10

huawei(config)#cable event alert report trap

huawei(config)#snmp-agent target-host trap-hostname huawei address 10.10.10.10 trap-paramsname docsis

huawei(config)#cable event alert report syslog

huawei(config)#cable event loghost ip 10.10.20.10

Configure the SHDSL service.

The MA5600T/MA5683T/MA5608T supports the SHDSL service of multiple encapsulation modes, such as IPoA, PPPoA, IPoE, and PPPoE. This topic uses the PPPoE mode as an example to describe how to configure the SHDSL service. For other encapsulation modes, see "Example: Configuring the xDSL Internet Access Service."

Configure the SHDSL line profile.

To configure the SHDSL line profile, run the shdsl line-profile add or shdsl line-profile quickadd command.

huawei(config)#shdsl line-profile quickadd 10 line two-wire rate 2048 2048 psd

symmetric transmission Annex-A remote disable probe disable snr-margin ds-curr 10 ds-worst

 10 us-curr 10 us-worst 10 bitmap 0x03

Configure the SHDSL alarm profile.

To configure the SHDSL alarm profile, run the shdsl alarm-profile add command.

In this example, the default profile (profile 1) is used.

Configure the SHDSL traffic profile.

To configure the SHDSL traffic profile, run the traffic table ip command.

In this example, the default profile (profile 1) is used.

Activate the SHDSL port.

huawei(config)#interface shl 0/5

huawei(config-if-shl-0/5)#deactivate all

huawei(config-if-shl-0/5)#alarm-config all 1

huawei(config-if-shl-0/5)#activate all 10

huawei(config-if-shl-0/5)#quit

Configure the upstream port.

The SHDSL users of MA5600T/MA5603T/MA5608T-2 use the PPPoE authentication. In this case, the smart VLAN is used to identify the users.

huawei(config)#vlan 3020 smart

huawei(config)#port vlan 3020 0/19 0-1

Add the service port.

Ports 0-15 of the SHDSL board in 0/5 provide the SHDSL services.

To add service ports in batches, run the multi-service-port command.

huawei(config)#multi-service-port vlan 3020 port 0/5 0-15 vpi 0 vci 35

rx-cttr 6 tx-cttr 6

Configure the SHDSL service.

The MA5600 supports the SHDSL Internet access service in multiple encapsulation modes, such as IPoA, PPPoA, IPoE, and PPPoE.

Configure the SHDSL line profile.

To configure the SHDSL line profile, run the shdsl line-profile add or shdsl line-profile quickadd command.

huawei(config)#shdsl line-profile quickadd 10 line two-wire rate 2048 2048 psd symmetric transmission Annex-A remote disable probe disable snr-margin ds-curr 10 ds-worst 10 us-curr 10 us-worst 10 bitmap 0x03

Configure the SHDSL alarm profile.

To configure the SHDSL alarm profile, run the shdsl alarm-profile add command.

In this example, the default profile (profile 1) is used.

Configure the SHDSL traffic profile.

To configure the SHDSL traffic profile, run the traffic table command.

In this example, the default profile (profile 1) is used.

Activate the SHDSL port.

huawei(config)#interface shdsl 0/5

huawei(config-if-shdsl-0/5)#deactivate all

huawei(config-if-shdsl-0/5)#alarm-config all 1

huawei(config-if-shdsl-0/5)#activate all profile-index 10

huawei(config-if-shdsl-0/5)#quit

Configure the upstream port.

The SHDSL users of MA5600-2 use the PPPoE authentication. In this case, the smart VLAN is used to identify the users.

huawei(config)#vlan 1300 smart

huawei(config)#port vlan 1300 0/7 0-1

Add the service port.

Ports 0-30 of the SHDSL board in slot 0/5 provide the SHDSL services. To add service ports in batches, run the multi-service-port command.

huawei(config MA5600T )#multi-service-port vlan 1300 port 0/5 0-31 vpi 0 vci 35 rx-cttr 6 tx-cttr 6

Configuring the Attributes of an Uplink GPON Port

How to query the statistics for a port, set the working mode of an optical module, and set the alarm thresholds for the receive optical power of the optical module through an uplink Huawei GPON   port.

When dual GPON ports are used for upstream transmission, only 0/0/2 port can be set. After the setting, the parameters of port 0/0/2 are the same as those of port 0/0/1.

To set the password for registering with an OLT through a GPON port, set the lower limit for the receive optical power of an optical module to 5 dBm and the upper limit for the receive optical power to 50 dBm, set the working mode of the optical module of the uplink PON port to auto, run the following command:
huawei(config-if-gponnni-0/0/1)#password
{ passwordvalue<S><Length 1-10> }:huawei

  Command:
          password huawei
huawei(config-if-gponnni-0/0/1)#optical-module threshold rx-power lower-limit 5 upper-limit 50
{ <cr>|bias<K>|temperature<K>|tx-power<K>|voltage<K> }:

  Command:
          optical-module threshold rx-power lower-limit 5 upper-limit 50
huawei(config  MA5600T -if-gponnni-0/0/1)#laser auto

Configuring Local Management (Through a Serial Port)

This topic describes how to connect the maintenance terminal to the MA5620/MA5626 through a local serial port, log in to the MA5620/MA5680T, and then manage the MA5620/MA5626 from the maintenance terminal.

Connect the serial port cable.
Use a standard RS-232 serial port cable to connect the serial port of the PC to the CONSOLE port (maintenance serial port) on the control board of the MA5620/MA5626, as shown in Figure 1.
Start the HyperTerminal.
Set up a connection.
Choose Start > Programs > Accessories > Communications > HyperTerminal on the PC. The Connection Description dialog box is displayed. Enter the connection name, as shown in Figure 3, and click OK.
Figure 3 Setting up a connection
Set the serial port.
On the PC that is connected to the MA5620/MA5626, select the number of the PC terminal serial port. You can select "COM1" or "COM2". In this example, "COM2" is selected, as shown in Figure 4. Click OK.
Figure 4 Selecting the serial port ID
Set the communication parameters of the HyperTerminal.
Set the parameters in the COM2 Properties dialog box, as shown in Figure 5. The parameters are as follows:
Baud rate: 9600 bit/s
Data bit: 8
Parity: None
Stop bit: 1
Flow control: None

NOTE:
The baud rate of the HyperTerminal must be the same as that of the serial port on the MA5620/MA5626. By default, the baud rate of the serial port on the MA5620/MA5626 is 9600 bit/s.
There may be illegible characters in the displayed input information after you log in to the system. This is because the baud rates between the HyperTerminal and the MA5620/MA5626 are not the same. In this case, set a different baud rate to log in to the system. The system supports the baud rates of 9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, and 115200 bit/s.

Configuring the Ethernet OAM

How to configure the Ethernet OAM on the MA5612

Create a VLAN.
The VLAN ID is 100, and the VLAN is a smart VLAN.
huawei(config)#vlan 100 smart
Add an upstream port to the VLAN.
Add port 0/7 to VLAN 100.
huawei(config)#port vlan 100 0/7 0
(Optional) Set the native VLAN of the port.
This step is to set the packets of the upstream Ethernet port to or not to carry the VLAN tag. Whether the native VLAN needs to be set for the upstream port depends on whether the upper-layer device connected to the upstream port supports packets carrying a VLAN tag. The setting on the MA5600 must be the same as that on the upper-layer device. In this example, the Ethernet packets are of the untagged type.
huawei(config)#interface scu 0/7
huawei(config-if-scu-0/7)#native-vlan 0 100
huawei(config-if-scu-0/7)#quit
Configure an MD.
MDs with the same index or level cannot be created.
The name format and the name of an MD must be unique.
The total length of the names of an MD and its MAs cannot be longer than 44 characters.
huawei(config)#cfm md 2 name-format string huawei level 3
Configure an MA.
The system supports up to 4096 MAs and each MD can be configured with up to 48 MAs. That is, if an MD is configured with 4096 MAs, the other MDs in the system cannot be configured with any MA. An MA of a non-existing MD cannot be created. An existing MA cannot be created again.
The total length of the names of an MD and its MAs cannot be longer than 44 characters.
huawei(config)#cfm ma 2/6 name-format string huawei-6 vlan 100
Configure an MEP.
MEP refers to the maintenance association end points. Ethernet OAM is used to test the link connectivity by using the MEPs at the two ends of a maintenance channel.
By default, the MEP management function is enabled, the priority of sending CFM packets is 7, and the function of sending CC packets is enabled.
huawei(config)#cfm mep 2/6/0 mepid 260 direction outward port
0/7/0 priority 7
Configure an RMEP.
By default, the detection function of the RMEP is disabled.
huawei(config)#cfm remote-mep-detect enable
(Optional) Set the interval for the MA to transmit CCMs. By default, the interval is one minute.
huawei(config)#cfm ma 2/6 cc-interval 10m
Enable the local CFM globally. By default, the local CFM is disabled globally.
huawei(config)#cfm enable
Enable the detection function of the remote MEP detection globally. By default, the remote MEP detection is disabled globally.
huawei(config)#cfm remote-mep-detect enable
Save the data.
huawei(config)#save

 NOTE:
Configuration on Huawei MA5600 B is the same as that on MA5600_A and it is not repeated here.

Configuring Interface Isolation

The S2350 and LS-S2326TP-EI-AC   support isolation at Layer 2 and interworking at Layer 3.

Run:
system-view
The system view is displayed.
(Optional) Run:
port-isolate mode { l2 | all }
Interface isolation is configured.
Run:
interface interface-type interface-number
The Ethernet interface view is displayed.
Run:
am isolate { interface-type interface-number }&<1-8>
Unidirectional isolation is configured on the Ethernet interface.
NOTE:
If interface A is isolated from interface B unidirectionally, packets sent from interface A cannot reach interface B, but packets sent from interface B can reach interface A.
Run:
system-view
The system view is displayed.
(Optional) Run:
port-isolate mode { l2 | all }
Interface isolation is configured.
By default, ports are isolated at Layer 2 but can communicate at Layer 3.
Run:
interface interface-type interface-number
The Ethernet interface view is displayed.
Run:
port-isolate enable [ group group-id ]
Interface isolation is enabled on the Ethernet interface.
By default, interface isolation is disabled.
 NOTE:
Interfaces in an interface isolation group are isolated from each other, but interfaces in different interface isolation groups can communicate. If group-id is not specified, interfaces are added to interface isolation LS-S2326TP-SI-AC   group 1.

Configuring the Unicast Negotiation Function for a Client

The unicast negotiation function and parameters for a connection between a client and a clock server are configured on the HUAWEI NE40E-X3  /NE40E-X8   functioning as a 1588 ACR client.

Run:
system-view
The system view is displayed.
Run:
ptp-adaptive enable
1588 ACR is enabled.
Run:
ptp-adaptive device-type client
The 1588 ACR clock working mode is set to client.
(Optional) Run:
ptp-adaptive frequency profile
The 1588 ACR-enabled device to totally comply with ITU-T G.8265.1 is configured.
By default, a 1588 ACR-enabled device complies with ITU-T G.8265.1 partially.
After the ptp-adaptive frequency profile command is run, the default domain value changes to 4. The domain value range changes to 4-23.
(Optional) Run:
ptp-adaptive domain domain-value
A 1588 ACR domain is configured.

NOTE:
The client and clock server, which exchange 1588v2 packets for clock or time synchronization, must be in one 1588 ACR clock domain.

Configuring the ISDN PRA Service

This topic is applicable to the scenario where the ISDN users are connected to the Huawei MA5680T   /MA5603T/MA5608T through the ISDN primary rate interface (PRI).

Add the EDTB board.
According to the data plan, add an ISDN PRA service board to slot 0/2.
huawei(config)#board add 0/2 h802EDTB
Add an IUA link set and IUA links.
In the SIGTRAN mode, configure the SIGTRAN protocol stack. Add an IUA link set, and then add IUA links.
huawei(config)#sigtran
huawei(config-sigtran)#iua-linkset add 1 mgid 0 jointly-work enable trafficmode override
iid-map 2 pendingtime cs-mode client
huawei(config-sigtran)#iua-link add 15 1 1401 10.13.4.116 1400 10.14.1.2
jointly-work-with primary-mgc priority 3
 NOTE:
All the ISDN call control messages are sent from the IUA link to the softswitch, whereas the system uses the bearer control messages to communicate with the softswitch through H.248.
Configure the ISDN PRA user data.
huawei(config-sigtran)#quit
huawei(config)#esl user
huawei(config-esl-user)#mgprauser add 0/2/0 0 1 interfaceid 1 terminalid 512

 NOTICE:
Each ISDN PRA user occupies 32 TIDs. You need to input only the first TID when adding an ISDN PRA user.
When the TID profile to which the ISDN PRA user of the MG interface is bound is not a layering profile, the TID must be configured and cannot be within the configured TID range.
When the TID profile to which the ISDN PRA user of the MG interface is bound is a layering profile, the configuration MA5600T    of the TID parameter is not available because the system automatically allocates the TID.

Configuring the Sub-interface

Configure ME60 

# Configure link layer protocol as FR on POS 1/0/0 of ME60 A.

<HUAWEI> system-view

[HUAWEI] sysname ME60A

[ME60A] interface pos 1/0/0

[ME60A-Pos1/0/0] link-protocol fr

[ME60A-Pos1/0/0] undo shutdown

[ME60A-Pos1/0/0] quit

# Configure the sub-interface POS 1/0/0.1 on ME60 A, and assign VC for it.

[ME60A] intrface pos 1/0/0.1 p2p

[ME60A-Pos1/0/0.1] ip address 202.38.160.1 255.255.255.0

[ME60A-Pos1/0/0.1] undo shutdown

[ME60A-Pos1/0/0.1] fr dlci 50

[ME60A-fr-dlci-Pos1/0/0.1-50] quit

# Configure the sub-interface POS 1/0/0.2 on ME60 A, and assign VC for it.

[ME60A] interface pos 1/0/0.2 p2p

[ME60A-Pos1/0/0.2] ip address 202.38.161.1 255.255.255.0

[ME60A-Pos1/0/0.2] undo shutdown

[ME60A-Pos1/0/0.2] fr dlci 60

[ME60A-fr-dlci-Pos1/0/0.2-60] quit

# Configure the static routes from ME60 A to LAN2 and LAN3.

[ME60A] ip route-static 129.10.0.0 255.255.0.0 202.38.160.2

[ME60A] ip route-static 129.11.0.0 255.255.0.0 202.38.161.2

 NOTE:

This example mainly explains sub-interface configuration. ME60 B and ME60-X3     do not require sub-interfaces configuration.

Configuration Example of the RADIUS Authentication

The MA5620    is interconnected with the RADIUS server through the RADIUS protocol to implement authentication.

Configure the authentication scheme.

Configure authentication scheme newscheme (users are authenticated through RADIUS).

huawei(config)#aaa

huawei(config-aaa)#authentication-scheme newscheme

huawei(config-aaa-authen-newscheme)#authentication-mode radius

huawei(config-aaa-authen-newscheme)#quit

huawei(config-aaa)#quit

Configure the RADIUS protocol.

Create RADIUS server template template1. RADIUS server 10.10.66.66 functions as the primary authentication server, and RADIUS server 10.10.66.67 functions as the secondary authentication.

huawei(config)#radius-server template template1

 Note: Create a new server template

huawei(config-radius-template1)#radius-server authentication 10.10.66.66 1812

huawei(config-radius-template1)#radius-server authentication 10.10.66.67 1812 secondary

huawei(config-radius-template1)#quit

Create a domain.

Create domain isp1.

huawei(config)#aaa

huawei(config-aaa)#domain isp1

  Info: Create a new domain 

Reference the authentication scheme.

You can reference an authentication scheme in a domain only after the authentication scheme is created.

huawei(config-aaa-domain-isp1)#authentication-scheme newscheme

Reference the RADIUS server template.

You can reference a RADIUS server template in a domain only after the RADIUS server template is created.

huawei(config-aaa-domain-isp1)#radius-server template1

huawei(config-aaa  MA5680T   -domain-isp1)#quit

How to configuring Huawei MA5600

Configure MA5600    the IP address of the L3 interface.

huawei(config)#vlan 2 smart

huawei(config)#port vlan 2 0/7 0

huawei(config)#interface vlanif 2

huawei(config-if-vlanif2)#ip address 10.0.0.1 24

huawei(config-if-vlanif2)#quit

Enable OSPF and specify the area ID to which the interface belongs.

huawei(config)#ospf

huawei(config-ospf-1)#area 0

huawei(config-ospf-1-area-0.0.0.0)#network 10.0.0.0 0.0.0.255

huawei(config-ospf-1-area-0.0.0.0)#quit

huawei(config-ospf-1)#quit

Configure the OSPF router ID.

huawei(config)#router id 1.1.1.1

Configure three static routes.

huawei(config)#ip route-static 20.0.0.1 32 vlanif 2

huawei(config)#ip route-static 30.0.0.1 32 vlanif 2

huawei(config)#ip route-static 40.0.0.1 32 vlanif 2

Import static routes into the OSPF routing table to improve its capability of obtaining routes.

huawei(config)#ospf

hawei(config-ospf-1)#import-route static

hawei(config-ospf-1)#quit

Save the  MA5600T    data.

huawei(config)#save

5680t 813e data do

MA5680T   813e, the data do, what is the business of the VLAN command?

8.1 EPON ONT template

EPON ONT template includes DBA template, template, template line business, this task introduce these template configuration.

8.2 create VLAN

Creating the VLAN VLAN base configuration and business, in the VLAN configuration before the need to ensure that VLAN has been created according to the actual planning.

8.3 uplink port configuration

Uplink docking port and the upper equipment, in order to make the data on the device can be forwarded to the network through the uplink port, and transmitting data upper network forwarding to the uplink port user side.

Configure EPON ONT 8.4

MA5680T/MA5683T provides services to end users through the ONT, MA5680T/MA5683T and ONT channel up, MA5680T/MA5683T to manage ONT, ONT to work properly.

Configure the EPON port 8.5

The Huawei GPON   port must be opened to work properly and bearing business, the task of open EPON port configuration port, and related properties.

8.6 to create EPON service flow

Configuring Remote Port Mirroring

Remote mirroring is not applicable to the NE80E/NE40E-X3   in the LDP over TE and TE links switchover scenarios.

Run:

system-view

The system view is displayed.

Run:

interface interface-type interface-number

The interface view is displayed.

Run one of the following commands as required:

Run the port-mirroring instance-name inbound [cpu-packet ] command to observe the inbound traffic on the remote mirroring port.

Run the port-mirroring instance instance-name outbound command to observe the outbound traffic on the remote mirroring port.

Run the port-mirroring remote { inbound | outbound } command to configure NE40E-X8   remote port mirroring for inbound or outbound traffic.

PPPoE current mirror

A few days ago to do with MA5620 , has no, today found a 9303 try, finally!!

Observe-port 1 interface GigabitEthernet1/0/0

Add the observation port

ACL number 5000

Rule 1 permit 0x00000050 0x0000ffff 42

Add user defined ACL, matching the target TCP 80 port, TCP protocol at the start of the two layer packets of thirty-fourth bytes, 2 bytes source port, destination port 2 bytes, 6 bytes plus PPPoE protocol, PPP protocol byte offset from the beginning of 2, forty-second bytes

Traffic classifier web operator or precedence 5

If-match ACL 5000

#

Traffic behavior Web

Mirroring to observe-port 1

#

Traffic policy Web

Classifier web behavior Web

Standard three piece suit

Interface GigabitEthernet1/0/6

Port link-type access

Port default VLAN 106

Traffic-policy web inbound

Business application port ACL, found ACL involves two layer data only in the direction of application, unable to make the direction

The final catch all monitoring equipment MA5626   is the destination port for the TCP 80 package

How to configure FTP for Huawei S5700 ?

When I configure FTP for Huawei S5700 switch, I use the steps as following, but I can’t make it work:

Step 1 seting for the FTP server

Start the FTP service on Switch, and configure the FTP username ftpuser, password ftppwd.

<Quidway> System-View

[Quidway] FTP server enable

[Quidway] AAA

[Quidway-aaa] local-user ftpuser password simple ftppwd - appear the mistake: Error: Unrecognized command found at '^' position. but if input: local-user ftpuserpassword CI ftppwd is not this tip.

[Quidway-aaa] local-user ftpuser service-type FTP

[Quidway-aaa] local-user ftpuser ftp-directory flash:/

[Quidway-aaa] return

Step 2 configure device IP

The configuration of IP, recommend the use of the idle and configured as a default configuration interface, the Ethernet 0/0/1 as an example.

<Quidway> System-View

[Quidway]interface Ethernet 0/0/1 - enter the mistake this command: Error: Wrongparameter found at position. and then give '^' not the next step.

[Quidway-Ethernet0/0/1]port link-type access

[Quidway-Ethernet0/0/1]quit

[Quidway] VLAN 10

[Quidway-vlan10] port Ethernet 0/0/1

[Quidway-vlan10] quit

[Quidway] interface vlanif 10

[Quidway-Vlanif10] IP address 1.1.1.1 24

[Quidway-Vlanif10] quit

[Quidway]

Step 3 login to the FTP server (Switch)

The following example is the WindowsXP system are described.

Storage will upload the file to the specified directory (assumed to be the D:\> directory), in the "Start Menu" run ", type" CMD, and then press the "enter" key. Then type FTP 1.1.1.1,in "user" prompt, enter the user name, in the "password" prompt, enter the password, and then press the "enter" key. Display information as follows:

D:\>ftp 1.1.1.1

Connected to 1.1.1.1

220 FTP service ready

User (1.1.1.2: (none)): ftpuser

331 Password required for 1

Password

230 User logged in

Ftp>

Step 1 upload web software

In the FTP client (PC) to execute the put source-filename [destination-filename], from PC upload software. Upload finished, execute the bye command, disconnect FTP, return to the user view.

Ftp> put D:\S2300.web.zip

200 Port command okay

150 Opening ASCII mode data connection for LS-S2326TP-SI-AC .web.zip

226 Transfer complete

Ftp: send 4940436 bytes, when using 35.10Seconds 140.76Kbytes/sec

Ftp> bye

221 Server closing

D:\> 

Configuring the License Function

With the license platform enabled, the license platform performs license control through license server over the function entries and resource entries supported by the MA5620  /MA5603 and provides customized services for users.

The license platform provides the registration mechanism for the service modules of the MA5600/MA5603. During system initialization, the service modules need to register for the controlled resource entries or the controlled function entries. After the system starts to work, based on the controlled entries that are registered, the license client management module obtains the authentication information about the license controlled entries of the MA5600/MA5603 from the license server.

If you need to use the license platform supported by the MA5600/MA5603, ensure to consider the deployment of the license server in network planning.

It is recommended that you install the license server on the same computer with the NMS server. If there is no NMS server, you need to separately deploy a license server on the network.                                                                                         

To configure the MA5600/MA5603 to communicate with the server through smart VLAN 10, configure the IP address of the L3 interface to 10.10.10.10/24, configure the MA5600/MA5603 to communicate with the license server (IP address: 10.20.20.2/24) through port 0/7/0, and configure the TCP port ID to 10010, do as follows:

huawei(config)#vlan 10 smart

huawei(config)#port vlan 10 0/7 0

huawei(config)#interface vlanif 10

huawei(config-if-vlanif10)#ip address 10.10.10.10 24

huawei(config-if-vlanif10)#quit

huawei(config)#ip route-static 0.0.0.0 24 10.10.10.1

huawei(config)#license esn 10.10.10.10

huawei(config)#license server ipaddress MA5626   10.20.20.2 tcpport 10010

NE40E with the single board:

LPUF-10 is a 10G  NE40E-X8   single board, 4 card slots,

Can support rich sub card type, support different types of card shuffling

The single board FIBv4 capacity of 1M, FIBv6 capacity is 256K, ACL for 16K, support 256K queue

LPUF-20 is a 20G single board, 2 card slots,

The single board support only to Prince card

The single board FIBv4 capacity of 1M, FIBv6 capacity is 256K, ACL for 16K, support 256K queue

LPUF-20 card is mainly divided into 4 kinds, one kind is the P20 card, which was divided into the general sub card and densified to Prince card

A class is a P20-A card, the card supports the 1588V2 function

In a class is a P20-B card, the card can support BRAS function,

The last category is the P20-E card, the card will not only support 1588V2 and BRAS, also support the enhanced QOS function, support 256K streams queues

LPUF-40 is a 40G single board, 2 card slots,

The single board support only to Prince card, have stronger forwarding capability greater port density

The single board FIBv4 capacity of 3M, FIBv6 capacity is 1M, ACL reached 32K, support 512K queue

LPUF-100 single board 4 card slots, support 100GE, 10GE, 40Gpos interface

LPUF-100 has a strong performance, support for 3M FIBv4, 1M FIBv6, 1M ACL, 512K queue,

100G series single board includes three types: high specification LPUF-100 and specifications of LPUI-100 and low LPUS-100 specifications.

LPUF-100 is a flexible card, 512K streams queues, can support 10GE, GE, 10G POS, 40G POS and other flexible configuration;

LPUI-100 is a fixed Ethernet interface board, 256K streams queues, meet the QoS scene secondary demand.

Types can offer include 10 x 10GE, 16 x 10GE line speed of convergence, 96 * GE, single port 40G POS and single port 100GE and other types of.

LPUS-100 is a fixed Ethernet interface board, 8 queues per port.

From the industry point of view, the current NE40E-X3   with 100G single board interface type, the highest density of the most abundant port.

Huawei participating GITEX will release the latest cloud data center solution

A leading telecom solutions provider Huawei NE40E , with a series of new products and solutions, to hold in the Dubai Bay area most influential exhibition -- GITEX ICT. Huawei will in this exhibition to demonstrate its complete ICT solutions, will also host channel salon, booth Open Speech abundant exhibition activities, concentrated display of the enterprise market Huawei technology and business trends in the development of understanding. As the key content of this exhibition, will be released to the industry's new cloud data center solution.

The vigorous development of cloud computing technology, has become a global hot topic and a hot spot for investment, cloud computing high efficiency, low cost, low power consumption, Gao Linghuo has many enterprises to the attention and favor, can help enterprises to achieve business development, innovation. In this context, Huawei at the GITEX show special show leading cloud computing technology and application in various industries. Focused on products including the new data center Huawei solution; at the same time, will also launch new high-end HVS storage system Smart based on Matrix architecture.

In this exhibition, the Middle East region Huawei vice president of business department Dong Wu said: "GITEX provides a platform for us, to display their latest products and solutions, let us have the opportunity to share best practices and from different countries worldwide customers, further consolidate and cooperation between partners and customers. To this end, we will organize and actively participate in various activities in the exposition, with partners and customers in-depth exchanges."

Huawei company will introduce its CloudEngine series switch products to customers in the Middle East in GITEX. The CloudEngine 12800 series switch is the next generation data center switches the highest industry performance, the maximum support 48Tbps exchange capacity, three times in the industry level; support each slot 2Tbps bandwidth (can upgrade to 4Tbps), four times the industry level. The CloudEngine 12800 series and CloudEngine 5800/6800 series of core switch cabinet top type switches support high densities of 100GE, 40GE, 10GE and GE interface, and full support of virtual network computing, storage, network support, the fusion of characteristics, which can meet the 4 generation server development for the next 10 years demand for network, help customers to build long-term stable the data center network infrastructure.

Not only that, Huawei will also in the GITEX such a platform to display the comprehensive strength Huawei enterprise network products, including the S9700 T bit core routing switch, with 21us industry minimum inter frame delay of the industry's first enterprise level 802.11ac standard with WLAN AP prototype, leading the industry 2 times the performance of AR G3 enterprise routers, NE series of high-end service router NE40E and facing the global launch of the enterprises in the end router NE20E-S, while in transport and access network advantage products, including support for a maximum of 5 site and multi direction convergence of data transmission of microwave products RTN950, OTN technology will be extended to the access layer of the Mini OTN system OSN 1800, have group properties Hybrid MSTP OSN 550, more than 11 years of commercial experience in xPON solution SmartAX MA5616.

The afternoon of October 17th, Huawei will participate in the forum organizers held a cloud. The customer will share the recent deployment of virtual desktop cloud solution on how to change the operation of the United Arab Emirates university. Huawei also and participants will discuss cloud computing brings to industry changes,  NE40E-X8 and how to play a role in reducing energy consumption.

Configuring the Multicast Log

The communication between the MA5680T   /MA5683T   and the multicast log server must be normal.

huawei(config)#display file-server auto-backup cdr                

  ------------------------------------------------------------------------------

  Server type: Primary                                                         

  Trans mode : TFTP              //The transmission mode of the multicast log is TFTP. 

  IP address : 10.10.10.10       //The IP address of the multicast log server is 10.10.10.10.

  ------------------------------------------------------------------------------

  Current Server: Primary server

huawei(config)#display igmp config global                                      

  ----------------------------------------------------------------------       

  Authorization                         : enable                               

  Robustness variable                   : 2                                    

  General query interval(s)             : 125                                  

  V2 General query response time(0.1s)  : 100                                  

  V3 General query response time(0.1s)  : 100                                  

  Specific query interval(0.1s)         : 10                                   

  V2 Specific query response time(0.1s) : 8                                    

  V3 Specific query response time(0.1s) : 8                                    

  Specific query number                 : 2                                    

  V2 router present timeout(s)          : 400                                  

  User action report switch             : disable                              

  Preview switch                        : enable                               

  Recognition time(s)                   : 30                                   

  The time of reset preview-count       : 04:00:00                              

  Auto create log interval(h)           : 2                                    

  Uplink port mode                      : default                              

  Bandwidth management switch           : enable                                

  CDR auto report interval(s)           : 600                                  

  CDR auto report number                : 200                                  

  CDR switch                            : enable  //The multicast log report in CDR mode is enabled.

  IGMP Packet encapsulation             : all                                  

  IGMP ECHO switch                      : disable                              

  Router IP                             : 192.168.1.1                           

  Initial unsolicited report interval(s): 1                                    

  Query offline user switch             : -                                    

  BTV Forward Mode                      : Mvlan                                

  ---------------------------------------------------